Common maintenance and upkeep items for aluminum extrusion machine
The maintenance and upkeep of the aluminum extrusion mills refer to regular or irregular inspection.
Cleaning, lubrication, adjustment, replacement, and other items to maintain their good working condition.
The following are common maintenance and upkeep items for aluminum extrusion mills, as well as corresponding operating steps and precautions:
clean
Cleaning refers to regularly removing dust, oil, debris, and other debris on the aluminum extrusion mills to prevent it from affecting the movement of mechanical parts and the signal of the sensor.
Cleaning can improve the appearance and hygiene of the aluminum machine, and can also prevent some malfunctions.
When cleaning your aluminum extrusion machine, you need to follow the following steps and precautions:
Before cleaning, you need to cut off the power supply and wait for the aluminum machine to stop running completely.
Use a soft cloth or brush to gently wipe the surface of the aluminum extrusion mills to remove dust and dirt.
Avoid using hard objects or corrosive liquids to avoid scratching or damaging the surface.
Use a vacuum cleaner or compressed air to blow away debris and debris from inside the aluminum extrusion mills.
Be careful not to blow into sensitive components such as circuit boards or sensors.
Use a clean cloth or paper towel to wipe away any oil or water stains on the aluminum extrusion mills.
If there are stubborn oil or water stains, you can use neutral detergent or alcohol to deal with them.
After cleaning is completed, the aluminum machine needs to be checked for any damaged or loose parts and repaired or tightened in time.
Before restarting the aluminum extrusion mills, make sure it is completely dry and free of any residue.
lubricating
Lubrication refers to regularly adding lubricating oil or grease to the bearings, chains, and gears.
And other moving parts on the aluminum extrusion machine to reduce friction, lower temperature, and prevent wear and rust.
Lubrication can improve the operating efficiency and life of aluminum extrusion mills, and can also reduce noise and vibration.
When lubricating aluminum machines, you need to follow the following steps and precautions:
Before lubrication, you need to cut off the power supply and wait for the aluminum extrusion mills to stop running completely.
Use appropriate lubricants, such as engine oil, lubricating oil, grease, etc., and lubricate according to the amount and period specified in the instructions.
Do not use too much or too little lubricant to avoid waste or deficiency.
Use a lubricant, sprayer, or brush to evenly apply or spray lubricant to the parts that need lubrication.
Be careful not to let the lubricant come into contact with sensitive parts such as circuit boards or sensors.
After the lubrication is completed, the aluminum extrusion machine needs to be run for a period of time to allow the lubricant to penetrate and distribute on various components fully.
Before restarting the aluminum machine, remove excess lubricant and check for any leaks or blockages.
Adjustment
Adjustment refers to regularly checking various parameter settings on the aluminum extrusion mills, such as cutting speed.
Tool angle, pressure, etc., to adapt to different processing conditions and requirements.
Adjustment can improve the processing accuracy and quality of the aluminum extrusion mills, and can also prevent some failures from occurring.
When adjusting the aluminum machine, you need to follow the following steps and precautions:
Before adjusting, you need to cut off the power supply and wait for the aluminum extrusion machine to stop running completely.
Use professional instruments or tools to make adjustments, and make adjustments in accordance with the methods and scope specified in the instructions.
Do not change or exceed the original parameter settings at will to avoid damage or danger.
After the adjustment is completed, it is necessary to test whether the aluminum extrusion mills can work normally and check whether there are any abnormalities or errors.
Before restarting the aluminum machine, you must record the adjusted parameter settings and save them in an appropriate location.
Change
Replacement refers to regularly checking the wearing parts on the aluminum extrusion machine, such as knives, brushes, belts, etc., and replacing worn or damaged parts in time to ensure their normal operation.
Replacement can improve the performance and reliability of aluminum machines, and can also reduce repair costs and downtime.
When replacing an aluminum extrusion mill, you need to follow the following steps and precautions:
Before replacement, you need to cut off the power supply and wait for the aluminum machine to stop running completely.
Use original or qualified accessories and follow the steps and precautions specified in the instructions for replacement.
Do not use inferior or inappropriate accessories to avoid damage or danger.
After the replacement is completed, you need to check whether the old and new parts are installed correctly.
And firmly and test whether the aluminum extrusion machine can work typically.
Before restarting the aluminum extrusion mills, you need to dispose of the old parts and record the time and reason for replacement.
If you need to buy an aluminum extrusion machine, you can leave your information.
We will find the most suitable aluminum extrusion machine for you, you can also see our Facebook official website.
See if our news can meet your needs for the machine:https://www.facebook.com/extruderpress